I've been dabbling with solar since the pandemic mainly small USB type-A based stuff and a 100W panel which shorted on me last year thankfully with no magic smoke here in the UK and wanted something I could just grab and travel with especially abroad at short notice that wouldn't attract much attention. I found this Atem Power 200W blanket by accident around 3 months a go via a random internet search but couldn't find a way to get it imported to the UK. I contacted Vic offroad directly to ask about the included Anderson SB50 and PP cables to ensure they use the standard ARRL wiring convention which they thankfully do out of the box so I knew this kit would be perfect for my requirements.I tried ordering this from another supplier direct from the States but they couldn't process my order so in desperation I tried ordering from Amazon.com directly and my order was shipped out using DHL in record time. I was shocked to see how quick it was moving through the DHL network and it actually arrived a day earlier than the scheduled delivery date so I was chuffed to bits as we had a rare late August sunny day.The panel comes with a 5M extension cable terminated with standard grey Anderson SB50's on each end, an SB50 to PP30 short cable wired to the ARRL standard, a PP30 to 4 way cable with ends for 8mm, 5.5 x 2.5mm, 5.5 x 2.1mm and aviation plug.The panel is extremely well made and isn't too heavy to move between locations it has a very thick sturdy rubberised handle perfect for the inclement UK weather so even with a bit of rain on the folded panel its still very easy to grip. I decided to hook up the panel to some of my 12V LFP batteries the next day after placing the panel flat on the ground ensuring the panel was covered by the sun. I hooked up my existing LFP controller which puts out 14.6V using 10 AWG SB50 to MC4 cables ensuring the polarity was correct but I was getting no output what so ever so I decided to hook up the included MPPT controller and it fired up instantly. For some reason my old controller died without any warning so not the fault of this panel as it also produced no open circuit voltage on my existing Ecoflow 60W panel. It took me an entire afternoon to suss out how to set the controller to LFP basically you need to hook the controller to a battery and long press the "set" button until the LED begins to flash then you can short press to cycle through the various profiles which are clearly noted on the plastic casing. Around mid day, I was getting a stable 120W with very hazy partially cloudy conditions with fluffy clouds moving across the sky occasionally dropping to 90W as the conditions changed but the open circuit voltage from the controller was 15.4V so I hooked it up to a 12V 26Ah LFP battery which began to charge with no issues but the BMS would cut power after a couple of minutes so I was beginning to think the controller was faulty. After changing to to LFP later the same day which outputs a solid 14.3V the battery charged completely fine. In bright cloudy conditions with no sun I was getting around 50W going into the battery and it briefly shot up to 140W for a few seconds around 13:00 BST during a brief patch of clear sun so everything is working completely fine. In the summer months I'd expect to get around 160W plus in sustained sunny conditions so I'm more than happy with the output I've seen so far.If there is one negative with this kit I wish the cables were slightly thicker say 10 AWG but they are more than thick enough to charge your batteries at a reasonable rate. Instead of using the included 5M Anderson extension lead I used my 1M long 6 AWG SB50 lead feeding the controller from the panel which produced very stable power to my batteries. I just wish this had some kick stands on the back to make it easy angling the blanket towards the sun but for ultra portable travel setups you can't get much simpler than this. You just need to ensure you hook up a battery to the controller before connecting to the panel. The controller takes a few seconds to ramp up but it works extremely well. Unlike cheapy controllers this remembers the battery type once its been set which is excellent. The only negative about the controller is the cables use really small rings to hook to the terminals may be 4mm size I'm not sure but all the cables are well insulated so no issues there. I'm glad this came with prefitted cables to the solar input and battery terminals. There are 1 set of load terminals which I won't use but you could hook up something like some LED lights if you wanted. The controller has metallic fins on the underside which helps to get rid of the heat when it charges above 10 amps.This panel when folded up is extremely small and is only slightly larger than my Ecoflow 60W portable's profile so it will easily fit into a suitcase.So in summery this panel is extremely well made, works as advertised even here in the UK comes with all the cables you need to hook up to batteries and most power stations and comes with a half decent MPPT controller. Anderson SB50 cables are easy to obtain and the SB50 ensures you won't get any connection sparks or have any issues with polarity unlike with MC4 cables especially when extension cables are involved.I hope you found this review helpful. Thank you if you made it to the end.